Anyone know the surface area of a 6'7" HR?
Announcement
Announcement Module
Collapse
No announcement yet.
Hellrazor surface area?
Page Title Module
Move
Remove
Collapse
X

Elite
 Dec 2011
 1015

Jesus is coming, look busy!
Moving forward or just spinning faster? 6'0 90kg
5'8 RF Vanguard 32.2L FCS R2 quad
6'0 FST Dominator 34.8L FCS PC SF4 quad + stabiliser
6'0 FST Spitfire 34.9L FCS PC R2 quad + stabiliser
6'2 FST Jacknife 33.3L FCS PC quad front/rear TC Redlines/TC Aqualines
6'2 FST Hellfire 33.7L FCS PC R2 quad + stabiliser (x 2, yes 1 here, 1 there!)
6'4 FST Alternator 34.?L FCS PG7
6'5 FST Hellrazor 33.5L FCS R2 quad + stabiliser
6'7 FST Hellrazor 36.5L FCS R2 thruster
I'm on a bad connection right now so I can't get the compare function to work within a reasonable amount of time but here try this http://boardformula.com/showanimation/4007/4011/# this will compare the 6'5 and 6'7 HZs and give you their surface areas as part of the comparison in the Tech View.

Elite
 Dec 2011
 1015

Jesus is coming, look busy!
Moving forward or just spinning faster? 6'0 90kg
5'8 RF Vanguard 32.2L FCS R2 quad
6'0 FST Dominator 34.8L FCS PC SF4 quad + stabiliser
6'0 FST Spitfire 34.9L FCS PC R2 quad + stabiliser
6'2 FST Jacknife 33.3L FCS PC quad front/rear TC Redlines/TC Aqualines
6'2 FST Hellfire 33.7L FCS PC R2 quad + stabiliser (x 2, yes 1 here, 1 there!)
6'4 FST Alternator 34.?L FCS PG7
6'5 FST Hellrazor 33.5L FCS R2 quad + stabiliser
6'7 FST Hellrazor 36.5L FCS R2 thruster

Elite
 Dec 2011
 1015

Jesus is coming, look busy!
Moving forward or just spinning faster? 6'0 90kg
5'8 RF Vanguard 32.2L FCS R2 quad
6'0 FST Dominator 34.8L FCS PC SF4 quad + stabiliser
6'0 FST Spitfire 34.9L FCS PC R2 quad + stabiliser
6'2 FST Jacknife 33.3L FCS PC quad front/rear TC Redlines/TC Aqualines
6'2 FST Hellfire 33.7L FCS PC R2 quad + stabiliser (x 2, yes 1 here, 1 there!)
6'4 FST Alternator 34.?L FCS PG7
6'5 FST Hellrazor 33.5L FCS R2 quad + stabiliser
6'7 FST Hellrazor 36.5L FCS R2 thruster
By itself it doesn't mean a whole lot but when you are comparing one board with another of similar rocker and bottom contour it probably helps decide which would be faster because theoretically there will be more planing area. But a flat board with less surface area may still be faster than say a highly rockered board with more surface area. Rocker will effect how much surface area is in contact with the water and things like concaves can flatten out rocker thus giving back some of the surface area that rocker might have taken away.
Things like volume and plan shape also have an effect. These are the things shapers or designers play with and get the right balance for a board for a particular purpose and with their years of experience you have to take their word on what works how and for what  along with your own experience too of course. But if you'd never surfed I don't think knowing any (or all) of these parameters and their design principles would allow you to work out just how a board would perform. It's when you've experimented and experienced a few combinations of these parameters that you can start to work it out.Last edited by Slowman; 11162012, 04:20 AM.
Comment

Firewire Library
 Nov 2011
 2729

6'0  175lbs  30yrs  SoCal 
503 TG Baked Potato  506 RF Potatonator  506 WRF Vanguard  510 FST Unibrow  600 FST Michel Bourez  600 FST Alternator  602 FST Alternator Round  603 FST Artillery
Firewire Social: Facebook  Twitter  Vimeo  Youtube
Hey All, use my Firewire email, [email protected] for emergency issues, not my forum inbox. However, please avoid contacting me directly with questions on choosing a board, just use the glorious forum. Cheers!
yeah well put slowman!!
its a little hard to use it as an exact spec because boards vary and surface area doesn't tell you anything about volume, rocker or foam distribution. I personally like to look at where the area is over the length of a board. is it in the nose, center, tail etc. That will tell you more about how the board rides than just the total value of the surface area...
Comment

Thanks Slowman & Chris.
The reason I asked about the surface area is that I learned that a lower surface area board (of the same model) requires a bit more juice to plane and project a bigger surfer. I'm 6'3" 210lbs. The 6'7" HR I have does go well in the juice but at my size and the average SoCal wave, it loses some of its projection & planing in the slower flatter stuff so I may move up a bit with the same model maybe a 6'9". The FW bigger boards seem to put on too much thickness and float for my taste. I'd rather do a 6'11" HR at 2 5/8 thickness but it's not available and while i'm wishing, lets do a rounded pin eh? Say about 6'11", roughly 1375 sq. in., 3839L HR. The 6'7" floats and paddles me fine, no issues there.
G
Comment
Comment