Got my board back from vacation and the nice people at United airlines did this for me. I can feel the edge on this crack so i'm worried it might leak next time I go surfing. Should I just sand a put a skim of epoxy over?
Got my board back from vacation and the nice people at United airlines did this for me. I can feel the edge on this crack so i'm worried it might leak next time I go surfing. Should I just sand a put a skim of epoxy over?
Looks pretty nimor, if you can't feel it with your finger nail forget about it
If not, light sanding to create bonding, hot coat it with epoxy resin
165cms 89Kgs dry...working on that at the moment...but not working!!! :)
Potato 5'2" /Vanguard 5'6"/Potatonator 5'8"/ Spitfire 5'8" / Quadraflex 6'0" / Flexflight 9'0"
Fins: Elevons, Solus, Controlllers, Jordy,AM2,
I always think it's worth putting a small patch of fibreglass over a crack. Especially on an area like the rail. The lick of epoxy is probably sufficient and will make it water tight, but maybe not as permanently as it would be if you patched it.
6'0" - 77kg - 170lbs
502R FPT - DL front DS rears
506D RVG - Soar Powerbase DL
600Q FTJ/CBD - Soar Powerbase DL
604R FFE - Soar Powerbase DL
I'd use clear helicopter tape, it will be water tight, permanent and neat (if you can cut neatly!).Originally Posted by prjwebb
Jesus is coming, look busy!
Moving forward or just spinning faster?
5'8 RF Vanguard 32.2L FCS H3 quad
6'0 FST Dominator 34.8L FCS PC SF4 quad + stabiliser
6'0 FST Spitfire 34.9L FCS PC R2 quad + stabiliser
6'2 FST Jacknife 33.3L FCS PC quad front/rear TC Redlines/TC Aqualines
6'2 FST Hellfire 33.7L FCS PC R2 quad + stabiliser (x 2, yes 1 here, 1 there!)
6'4 FST Alternator 34.?L FCS PG7
6'7 FST Hellrazor 36.5L FCS R2 thruster
------------------------------------------
6'5 FST Hellrazor 33.5L FCS coming
I don't even know what that is!
6'0" - 77kg - 170lbs
502R FPT - DL front DS rears
506D RVG - Soar Powerbase DL
600Q FTJ/CBD - Soar Powerbase DL
604R FFE - Soar Powerbase DL
Here you go http://www.racerstape.com/heli.html and http://solutions.3m.com/wps/portal/3...lutions/Boots/ are just a couple of examples. It is tough polyurethane tape, the adhesive is very strong. I use it to protect the carbon frame on my bikes. It adheres that strongly that if you put it on incorrectly and try to take it off it will take the finish coat off with it. Originally used to protect the leading edge of carbon helicopter blades, hence the name.
Jesus is coming, look busy!
Moving forward or just spinning faster?
5'8 RF Vanguard 32.2L FCS H3 quad
6'0 FST Dominator 34.8L FCS PC SF4 quad + stabiliser
6'0 FST Spitfire 34.9L FCS PC R2 quad + stabiliser
6'2 FST Jacknife 33.3L FCS PC quad front/rear TC Redlines/TC Aqualines
6'2 FST Hellfire 33.7L FCS PC R2 quad + stabiliser (x 2, yes 1 here, 1 there!)
6'4 FST Alternator 34.?L FCS PG7
6'7 FST Hellrazor 36.5L FCS R2 thruster
------------------------------------------
6'5 FST Hellrazor 33.5L FCS coming
sounds pretty full on!
6'0" - 77kg - 170lbs
502R FPT - DL front DS rears
506D RVG - Soar Powerbase DL
600Q FTJ/CBD - Soar Powerbase DL
604R FFE - Soar Powerbase DL
I put a skim of epoxy over it last night but I will check that tape out for next time! seems like cool stuff
Indeed!!
165cms 89Kgs dry...working on that at the moment...but not working!!! :)
Potato 5'2" /Vanguard 5'6"/Potatonator 5'8"/ Spitfire 5'8" / Quadraflex 6'0" / Flexflight 9'0"
Fins: Elevons, Solus, Controlllers, Jordy,AM2,
Posting Permissions
Reply With Quote